Tri-fold tonneau cover
The Tri-Fold Tonneau Cover can be installed on the truck bed to protect your gear and cargo.
TRI-FOLD TONNEAU COVER REMOVAL
To remove the Tonneau Cover, use the following steps:
1. Open the tailgate to gain access to the rear pair of Tonneau Cover clamps located on the underside of the cover.
Location Of Rear Clamps
NOTE:
If clamp wire is damaged replace immediately.
2. Pull both clamp handles down to release the Tonneau Cover’s rear panel.
Released Position
3. From the released position, send the clamps to the Stowed Position by pushing from the yellow bumper up.
Stowed Position
CAUTION!
Make sure the Tonneau Cover clamp and clamp wire are in the proper stowed position. If the clamp and clamp wire are not properly stowed, damage to the Tonneau Cover material will result.
4. Fold the rear panel up onto the center panel (intermediate position).
NOTE:
○ When folding the center and rear panels, the sections MUST be held together to avoid damage to the cover material.
○ Fold the panels gently. It is not recommended to allow the panels to drop under their own weight.
Folded Rear Panel (Intermediate Position)
NOTE:
The vehicle cannot be driven when the Tonneau Cover is in this position.
5. Fold the rear and center panels up onto the front panel (Tri-Folded position).
Tri-Folded Position
Incorrect Folding — Will Cause Damage
Correct Folding — Hold Panels Together
6. Clip both stowage straps to prevent the Tonneau Cover panels from unfolding.
NOTE:
Be sure the Tonneau Cover has been folded completely, and the stowage straps are engaged, before removing.
CAUTION!
The folded Tonneau Cover must be latched by both front latches and both front stowage straps or damage to the Tonneau Cover or vehicle may occur.
Stowage Strap
7. Once in the Tri-Folded position, pull both front clamp handles down to the Released Position.
Released Position
8. From the Released Position, send the clamps to the Stowed Position by pushing from the yellow bumper up. Listen for a “clicking” sound to confirm the clamp has been properly stowed.
Stowed Position
9. With two people, remove the Tonneau Cover.
TRI-FOLD TONNEAU COVER INSTALLATION
To install the Tonneau Cover, use the following steps:
1. Position the folded Tonneau Cover on the pickup box and push the cover forward against the front of the pickup box. The Tonneau Cover centers itself when placed on the vehicle.
NOTE:
Make sure to always push the Tonneau Cover all the way forward on the pickup box. Failure to do so might prevent proper clamp engagement, or interfere with the tailgate auto drop function (if equipped).
Location Of Front Clamps
2. Pull down on the first set of clamp handles to release the clamps from the stowed position.
Stowed Position
3. Push clamp wires up and under the flange of the box (or flange of the Ram Box rail, if equipped) to the semi clamped position.
Semi Clamped Position
4. Push clamp handles upward to the clamped position to properly engage the clamps.
Clamped Position
NOTE:
Once clamped, be sure the clamps are not improperly attached to the truck bed flange.
Improper Clamp Position
5. Disengage the stowage straps.
6. Unfold the center and rear panels to the intermediate position.
Intermediate Position (Vehicle Cannot Be Driven)
NOTE:
When folding the center and rear panels, the sections MUST be held together to avoid damage to the cover material.
Incorrect Folding — Will Cause Damage
Correct Folding — Hold Panels Together
7. Completely unfold the Tonneau Cover.
Fully Unfolded Position
8. Pull the rear clamp handles down into the released position.
Stowed Position
9. Push clamp wires up and under the flange of box (or flange of Ram Box rail, if equipped) to the semi clamped position.
Semi Clamped Position
10. Push clamp handles upward to the clamped position to properly engage the clamps.
Clamped Position
Improper Clamp Position
NOTE:
Once clamped, be sure the clamps are not partially clamped to the truck bed flange.
CAUTION!
It is the driver’s responsibility to ensure the Tonneau Cover is properly installed on the vehicle. Failure to follow this procedure can result in detachment of the Tonneau Cover from the vehicle and/or damage to the vehicle/Tonneau Cover.
The Tonneau Cover clamps can be locked when in the clamped position by placing a lock through the locking hole.
Locking Hole
TRI-FOLD TONNEAU COVER CLEANING
For proper cleaning of the Tonneau Cover, use Mopar® Whitewall & Vinyl Top Cleaner and Mopar® Leather & Vinyl Conditioner/Protectant.